The LUMiFrac is an innovative adhesion analyser, which employs centrifugal forces to determine temperature-controlled tensile as well as shear strength.

It employs centrifugal forces to stress multiple samples at once. It provides adhesive and tensile strength as well as shear strength as an absolute physical quantity in N/mm² (MPa).

The LUMiFrac accomplishes this by directly applying an incrementally increasing centrifugal force to the specimen being tested. It determines with high resolution the RPM at the moment of fracturing (employing Centrifugal Adhesion Testing Technology).

All data is transmitted to the well-known and popular operating software SEPView, which automatically calculates and displays the critical force/strength of failure in real time. Furthermore, it allows to analyze, compare & calculate statistics and combine results for up to tens of samples. Related data, as figures of fracture pattern, may be taken into account as well.

The LUMiSpoc® is a highly advanced single particle analysis system, similar to a flow cytometer, that measures particle size distribution and particle concentration of nano- and microparticles in suspensions and emulsions with an unparalleled resolution and dynamic range.

The instrument uses the patented Single Particle Light-Scattering Technology® , a technology which records light that is scattered into into forward and sideward directions by single nano- and micro particles while passing a laser beam of a special beam cross-section.

It enables you to get a deep insight into complex nano- and submicro-particulate systems, which helps you to design tailored particles and dispersions.

The Burst Tester is used as a multi-directional test to identify failure in the direction showing least resistance. This test shows the physical strength and fiber bond. Different models are available for paper, board or textile. This instrument is also used for other applications such as plastic, rubber, aluminum and felts. The sample is pneumatically clamped, the rubber membrane is pushed upwards by hydraulics. The force at fracture is recorded.

Insert your sample and test The Horizontal Tensile Tester tests the tensile strength and elongation of a sample. After placing the sample the sensor detects the sample and the test starts. Special guides are supplied to center the sample correctly. The guides can be replaced when another test width is required. The wide workbench enables you to easily perform your tests. The auto detect option leaves your hands free to slide in your sample. The touchscreen has clear buttons makes navigation quick and easily. As an option, the instrument can be adapted for wet test according to ISO 12625-5. Test results After the tests the values are shown in a graph and in statistical values. The main results are force, strain, T.E.A, elongation and force, and there is a wide range of other results. The instrument is equipped with an overload protection and can be supplied with a 50, 100, 250, 500 or 1,000N load cell.

The 6MBA is the basic model offered within the Ray-Ran Range of Melt Flow Indexers. The manually operated test procedure is very simple to undertake. Molten Polymer is extruded through a closely controlled orifice (die) from the apparatus using pre set conditions of temperature and pressure produced by a dead weight system. The extruded polymer is cut off manually and is then weighed. Using the time interval to extrude the polymer its flow rate over 10 minutes can easily be determined, thus giving the Melt Flow Index (MFI) or Melt Mass Flow Rate (MFR) in g/10 min. By conducting a simple Density Test at test temperature on the same material using the same pre set conditions and a known piston travel distance the Melt Volume Rate (MVR) can also be determined.

Bulk density apparatus is testing equipment used to measure the bulk density property of powder, granules and other “divided” solids, especially used in reference to mineral components (soil, gravel, sand), chemical substances, (pharmaceutical), plastics like polyethylene (hdpe or mdpe) pvc, polystyrene etc, or foodstuff and any other masses of granular or particulate matter.

The Method A tester is primarily used to measure the apparent density of fine granules that can be poured readily through a “V” shaped funnel, the material under test is allowed to flow into a cylindrical cup with a known volume of 100cm³.

Oxygen And Carbon Dioxide Headspace Measurement For modified Atmosphere Packaged (MAP) Product

These highly advanced instruments are equipped with integral sampling systems, unique, miniature, long-life, zirconia and infrared sensors, and microprocessor control to deliver the most accurate and repeatable performance possible.

The internal microprocessor manages calibration, autoranging, flow control, test duration and many other functions to ensure consistent, error-free results. One touch automated calibration and product analysis make these analyzers easy to use. Response is typically less than five seconds for oxygen and ten seconds for carbon dioxide.

The new more compact corrosion resistant enclosure minimizes the required foot print space on carts and table tops.

Automated package sampling is easy. Measurement duration is user selectable which provides great flexibility for a large variety of products. Using the sample wand, insert the sampling needle into the package and press test. The instrument does the rest; extracting the sample, analyzing sensor output and holding the results for viewing on the bright autoranging display.

• Fast, accurate MAP analyser for testing low volumes of O2 and CO2 in gas flushed food and pharmaceutical products.